Grass-valley Kaleido-RCP2 Dec 16 2014 Bedienungsanleitung

Guide to Installation and OperationM735-9902-10416 December 2014

xNoticesThis equipment has been tested and found to comply with the requirements of the EMC directive 2004/108/EC:• EN 55022 Class A Radiated and cond

1Kaleido-RCP2The Kaleido-RCP2 is a compact control panel for the Kaleido multiviewers. Featuring direct key control for the most common commands, it

2Kaleido-RCP2Control Surface LayoutTwo kinds of power sources are supported:• midspan power source injector into an existing Ethernet network, and• po

3Kaleido-RCP2Guide to Installation and OperationLayout PresetsThe ten numbered keys laid out across the top of the panel are used to recall saved layo

4Kaleido-RCP2Control Surface LayoutAudioKeypadThe keypad buttons have double functions. Use the MOUSE LOCK button (top left) to switch between the two

5Kaleido-RCP2Guide to Installation and OperationConfigurationBefore you can use your Kaleido-RCP2 to operate your Kaleido system, you must set up the

6Kaleido-RCP2Selecting a Roomdisplay. To access the menu press and hold the ENTER button until the ESC button lights up, and then use the keys to navi

7Kaleido-RCP2Guide to Installation and Operationonly. In the example described below, the three rooms that are available, are listed in this sequence:

8Kaleido-RCP2Setting an IP Address, Subnet Mask and Gatewayaddress allocation). In our example, we suppose that the DHCP option is enabled, and must b

9Kaleido-RCP2Guide to Installation and OperationWhen you change the DHCP mode, the device must be restarted for the new option to take effect. This is

iiNoticesCopyright and Trademark NoticeCopyright © 2007–2014, Grass Valley USA, LLC. All rights reserved.Belden, Belden Sending All The Right Signals,

10Kaleido-RCP2Restoring Default Parametersconnections to Kaleido systems in its own subnet.To configure a unicast IP address on the Kaleido-RCP2, do t

11Kaleido-RCP2Guide to Installation and OperationIn addition, the current room and login position are erased from the Kaleido-RCP2 memory.Updating the

12Kaleido-RCP2Updating the Kaleido-RCP2 FirmwareFirmware Selection (Step 1 of 3)Make sure you fulfill the following conditions before beginning this p

13Kaleido-RCP2Guide to Installation and Operation2 Press ENTER to select the first option: ROOM SELECTION, and then wait until the room list is downlo

14Kaleido-RCP2Operation3 Select the first option, VERSION, by pressing ENTER again.The Kaleido-RCP2 displays the currently-installed version of the fi

15Kaleido-RCP2Guide to Installation and OperationEnabling/Disabling the Kaleido-RCP2 User InterfaceThe PANEL ENABLE button cycles the Kaleido-RCP2 bet

16Kaleido-RCP2Resetting the Kaleido-RCP2• All other keys on the Kaleido-RCP2 are disabled (LEDs off).• The LCD display is off.• Any peripherals (e.g.

Contact UsGrass Valley Technical SupportFor technical assistance, contact our international support center, at 1-800-547-8949 (US and Canada) or +1 51

iiiKaleido-RCP2Guide to Installation and OperationImportant Safeguards and NoticesThis section provides important safety guidelines for operators and

ivNoticesWarningsA warning indicates a possible hazard to personnel, which may cause injury or death. Observe the following general warnings when usin

vKaleido-RCP2Guide to Installation and Operation• When installing this equipment, do not attach the power cord to building surfaces.• Products that ha

viNoticesMesures de sécurité et avis importantsLa présente section fournit des consignes de sécurité importantes pour les opérateurs et le personnel d

viiKaleido-RCP2Guide to Installation and OperationAvertissementsLes avertissements signalent des conditions ou des pratiques susceptibles d’occasionne

viiiNotices• Après tout travail d’entretien ou de réparation, faites effectuer des contrôles de sécurité par le personnel technique qualifié.Mises en

ixKaleido-RCP2Guide to Installation and Operation• Pour plus de sécurité, vérifiez périodiquement la valeur de résistance du bracelet antistatique. El