RS-422 INTERFACE BOARDInstallation ManualPROFILE FAMILYVIDEO FILE SERVERS071-0519-01OCTOBER 2000
Certifications and Compliances10 RS-422 Interface Board InstallationCertificationCategory StandardSafety Designed/tested for compliance with: UL1950 –
RS-422 Interface Board Installation 11RS-422 Interface Board InstallationBefore You StartUse these instructions to remove and replace the Profile Vide
Before You Start12 RS-422 Interface Board InstallationKit Contents A list of kit contents is shown in Table 1. Tools Required Tools required, but not
Electrostatic PrecautionsRS-422 Interface Board Installation 13Electrostatic PrecautionsCAUTION: This product contains components that are highly sens
Installation Procedures14 RS-422 Interface Board InstallationInstallation ProceduresThis manual includes step-by-step instructions for removing and re
Removing the Chassis CoversRS-422 Interface Board Installation 15Removing the Chassis Covers Use the following procedure to remove the chassis covers:
Installation Procedures16 RS-422 Interface Board InstallationRemoving the Circuit Board Hold-down Brackets There are two hold-down brackets located in
Removing the Circuit Board Hold-down BracketsRS-422 Interface Board Installation 17Figure 2. Removing the circuit board hold-down brackets 9675-21342
Installation Procedures18 RS-422 Interface Board InstallationRemoving the RS-422 Interface BoardThe RS-422 Interface board is a half-height board inst
Removing the RS-422 Interface BoardRS-422 Interface Board Installation 192. Use the Torx tool with the T15 tip to remove the screw from the board moun
Copyright Copyright © 2000 Grass Valley Group Inc. All rights reserved. Printed in the UnitedStates of America.This document may not be copied in whol
Installation Procedures20 RS-422 Interface Board Installation3. Carefully remove the RS-422 Interface board by grasping the edge of the circuit board
Removing the RS-422 Interface BoardRS-422 Interface Board Installation 21Figure 5. Mounting screw location for full height board 9040-1312
Installation Procedures22 RS-422 Interface Board InstallationInstalling the RS-422 Interface BoardTo install the RS-422 interface board:1. Verify the
Installing the RS-422 Interface BoardRS-422 Interface Board Installation 232. Align the RS-422 board with the mother board connector in slot J17 (see
Installation Procedures24 RS-422 Interface Board InstallationReinstalling Board Hold-down Brackets Now that the RS-422 Interface board is installed, y
Reinstalling Board Hold-down BracketsRS-422 Interface Board Installation 252. Insert front hold-down bracket ( in Figure 9) into the board area and en
Installation Procedures26 RS-422 Interface Board Installation4. Place rear hold-down bracket ( in Figure 9 on page 25) over the boards.5. Align the f
Replacing the Profile Chassis CoversRS-422 Interface Board Installation 27Replacing the Profile Chassis CoversTo replace the Profile chassis covers:1.
Installation Procedures28 RS-422 Interface Board InstallationReplacing the RS-422 Board Interface CableThe kit includes a new interface cable for the
Installing the RS-422 Interface Board Device DriverRS-422 Interface Board Installation 29Installing the RS-422 Interface Board Device DriverNow that y
RS-422 Interface Board Installation 3Contents Grass Valley Group Product Support...
Installation Procedures30 RS-422 Interface Board InstallationInstalling the RS-422 Board Device DriverAfter removing the old RS-422 board device drive
Installing the RS-422 Interface Board Device DriverRS-422 Interface Board Installation 317. The Select OEM Option dialog box appears (see Figure 13).
Installation Procedures32 RS-422 Interface Board Installation8. When the RocketPort/RocketModem NT Setup window appears, shown in Figure 14, set Start
Installing the RS-422 Interface Board Device DriverRS-422 Interface Board Installation 339. From the Advanced menu (see Figure 14), select Options to
Installation Procedures34 RS-422 Interface Board InstallationVerifying InstallationNow you are ready to verify the RS-422 Interface board installation
Verifying InstallationRS-422 Interface Board Installation 35Figure 16. PDR Diagnostics window exampleSlot J1Slot J2Slot J3Slot J4Slot J5Slot J6Slot J7
Installation Procedures36 RS-422 Interface Board Installation5. When the RS422 Test window appears as shown in Figure 17, follow the on-screen instruc
Copying the Driver Diskette Contents to the System DriveRS-422 Interface Board Installation 37Copying the Driver Diskette Contents to the System Drive
Installation Procedures38 RS-422 Interface Board Installation
Contents4 RS-422 Interface Board Installation Figures1 Removing the front and rear chassis covers ... 15
RS-422 Interface Board Installation 5Grass Valley Group Product SupportYou can get technical assistance, check on the status of problems, or report ne
General Safety Summary6 RS-422 Interface Board InstallationGeneral Safety SummaryWARNING: These instructions are for use by qualified service personne
Product Damage PrecautionsRS-422 Interface Board Installation 7Do Not Operate inWet/DampConditionsTo avoid electric shock, do not operate this product
General Safety Summary8 RS-422 Interface Board InstallationTerms on theProductThese terms may appear on the product: DANGER indicates a personal injur
Certifications and CompliancesRS-422 Interface Board Installation 9Certifications and CompliancesFCC EmissionControlThis equipment has been tested and
Kommentare zu diesen Handbüchern