Grass-valley Kaleido-Modular-X v.7.70 Bedienungsanleitung

Quick Start GuideM933-9805-1082015-04-02KALEIDO-MODULAR-XHIGH PICTURE COUNT, ULTRA-FLEXIBLE AND SCALABLE MULTIVIEWER

6Setting Up Your Kaleido-Modular-X SystemPhysical Setup2 Identify the appropriate slots for your new cards.The following table shows the number of slo

7Kaleido-Modular-XQuick Start GuideInput C KMX-3901-IN-16-D Slots 11–14 Slot 13Input D KMX-3901-IN-16-D Slots 15–18 Slot 1748 × 4 Card Model Rear pane

8Setting Up Your Kaleido-Modular-X SystemPhysical Setup3 Remove the blank rear panels that cover the slots where you wish to install your cards, by re

9Kaleido-Modular-XQuick Start Guide7 Make the physical connections between your input and output cards, by using the FlexBridge cables that shipped wi

10Setting Up Your Kaleido-Modular-X SystemPhysical SetupExample: 4K UHD prescaler’s FlexBridge outputs A1 and B1, connected to 3G/HD SDI inputs 5 and

11Kaleido-Modular-XQuick Start Guide11 Connect your Kaleido-Modular-X output cards to displays that support this resolution.• Monitor wall displays: C

12Setting Up Your Kaleido-Modular-X SystemPhysical SetupKaleido-X User’s Manual, for instructions on how to create 4K UHD rooms and layouts.• Broadcas

13Kaleido-Modular-XQuick Start Guide15 Connect a reference source (if available) to one or more reference inputs.You can now proceed with the networki

14Setting Up Your Kaleido-Modular-X SystemPhysical SetupFlexBridge wiring for a 8 × 1 or 16 × 1 systemTo connect the input and output cards in a Kalei

15Kaleido-Modular-XQuick Start GuideFlexBridge wiring for a 32 × 2 systemTo connect the input and output cards in a Kaleido-Modular-X 32 × 21 Complete

iiNoticesCopyright & Trademark NoticeCopyright © 2013–2015, Grass Valley USA, LLC. All rights reserved.Belden, Belden Sending All The Right Signal

16Setting Up Your Kaleido-Modular-X SystemPhysical SetupFlexBridge wiring for a 48 × 2 systemTo connect the input and output cards in a Kaleido-Modula

17Kaleido-Modular-XQuick Start GuideFlexBridge wiring for a 32 × 4 systemTo connect the input and output cards in a Kaleido-Modular-X 32 × 41 Complete

18Setting Up Your Kaleido-Modular-X SystemPhysical SetupFlexBridge wiring for a 48 × 4 systemTo connect the input and output cards in a Kaleido-Modula

19Kaleido-Modular-XQuick Start GuideChanging the Output ResolutionTo change the display resolution from the Densité controller’s local control panel1

20Setting Up Your Kaleido-Modular-X SystemPhysical Setup4 Press the SEL button again.5 The current resolution for the monitor wall display that is con

21Kaleido-Modular-XQuick Start GuideThe Status LED on the selected card flashes orange, and the associated control menu appears on the LCD display of

22Setting Up Your Kaleido-Modular-X SystemNetworking Setupoutput card’s IP address doubles as the system IP address). Kaleido-Modular-X output cards a

23Kaleido-Modular-XQuick Start Guide• If you are setting up a single-head or a dual-head Kaleido-Modular-X, then replace the IP address for Output A w

24Setting Up Your Kaleido-Modular-X SystemNetworking SetupIP ADDRESS appears on the control panel’s display.6 Press the [–] button.NETWORK MASK appear

25Kaleido-Modular-XQuick Start Guide• If the control panel’s display shows KEEP SETTINGS, navigate to UPDATE SETTINGS by pressing the [–] button, and

iiiKaleido-Modular-XQuick Start GuideElectrostatic Discharge (ESD) ProtectionElectrostatic discharge occurs when electronic components are improperly

26Setting Up Your Kaleido-Modular-X SystemNetworking Setup• Press the [+] and [–] buttons, to change the digit at the current input position.• Press S

27Kaleido-Modular-XQuick Start GuideAfter a moment, the card restarts. The startup sequence takes approximately four minutes, during which time the St

28Setting Up Your Kaleido-Modular-X SystemNetworking SetupThe Status LED on the selected card flashes orange, and the associated control menu appears

29Kaleido-Modular-XQuick Start GuideFRAME IP ADDRESS EDIT appears on the control panel’s display.5 Press the [–] button.NETMASK EDIT appears on the co

30Setting Up Your Kaleido-Modular-X SystemNetworking SetupAfter a moment, the card restarts. The startup sequence takes approximately four minutes, du

31Kaleido-Modular-XQuick Start Guide4 Click the XAdmin button.5 If you see a security warning, or a certificate error message, then refer to Registeri

32Setting Up Your Kaleido-Modular-X SystemNetworking Setup9Under General, type the name you wish to use for your system.If there are more than one mul

33Kaleido-Modular-XQuick Start Guide12 Click Apply settings.The multiviewer must restart for changes to the network configuration to take effect. A me

34Setting Up Your Kaleido-Modular-X SystemNetworking Setup2 On the Kaleido-RCP2 unit, press the ENTER button and hold it until the ESC button lights u

35Kaleido-Modular-XQuick Start GuideTo configure the IP address and other network settings of the ABT1 Connect a PC to a switch.2 Referring to Configu

ivNoticesElectromagnetic CompatibilityThis equipment has been tested for verification of compliance with FCC Part 15, Subpart B requirements for class

36Setting Up Your Kaleido-Modular-X SystemNetworking SetupThe home page of the ABT’s built-in Web server is displayed.6Click Network Configuration (in

37Kaleido-Modular-XQuick Start GuideThe Properties window for the selected network adapter opens.4On the Networking tab, under This connection uses th

38Setting Up Your Kaleido-Modular-X SystemXEdit InstallationChanging an IP Address on Windows XPTo change the IP address of a client PC that has Windo

39Kaleido-Modular-XQuick Start GuideThe browser prompts you to save an executable file to your hard drive (Kaleido-windows32-online.exe1). This file i

40Setting Up Your Kaleido-Modular-X SystemXEdit InstallationDepending on your Windows Firewall settings, a security alert may appear.•Click Allow acce

41Kaleido-Modular-XQuick Start GuideFor more information about calibrating your system, configuring rooms, creating layouts, and operating the monitor

42Setting Up Your Kaleido-Modular-X SystemSystem Verification2 Click the XAdmin button.3 If you see a security warning, or a certificate error message

43Kaleido-Modular-XQuick Start Guide7 Review the information on this page, to make sure your input and output cards are all properly interconnected. I

44Setting Up Your Kaleido-Modular-X SystemSystem Verification11 Review the enabled input and output options, and the main system statuses of the Kalei

45Kaleido-Modular-XQuick Start GuideA layout browser appears on the displays associated with the current room.3 Select the layout you wish to load fro

1Setting Up Your Kaleido-Modular-X SystemWelcome to the Kaleido family of multiviewers! This Quick Start Guide is designed to help you get your Kalei

46Setting Up Your Kaleido-Modular-X SystemSystem VerificationFRAME IP ADDRESS EDIT appears on the control panel’s display.3 Press the SEL button again

47Kaleido-Modular-XQuick Start GuideThe Status LED on the selected card flashes orange, and the associated control menu appears on the display of the

48Setting Up Your Kaleido-Modular-X SystemRS-422 Connection DiagramStandard wiring between multiviewer and devices wired to SMPTE “slave” specificatio

Contact UsGrass Valley Technical SupportFor technical assistance, contact our international support center, at 1-800-547-8949 (US and Canada) or +1 51

2Setting Up Your Kaleido-Modular-X SystemIntroductionthe KX Router logical router, or to control other logical routers configured within your multivie

3Kaleido-Modular-XQuick Start GuideGetting OrganizedThis section provides information about system requirements, and items shipped with your Kaleido-M

4Setting Up Your Kaleido-Modular-X SystemGetting Organized• 2 WECO analog audio mating connectors for each output card• 2 serial port adapters (1 with

5Kaleido-Modular-XQuick Start Guide• A dedicated 100Base-T Ethernet switch with enough ports for the KMX-3901-OUT output cards, the housing frames’ De