Grass-valley K2 Summit Client Quick Start Nov.23 2009 Bedienungsanleitung PDF herunterladen

Connections per channel (C1, C2, etc)

K2 Summit

Production Client

Quick Start Guide

Before you begin, unpack the following items...

071-8722-00 October 27, 2009

...and locate the documentation you need.

C2 C3 C4

~AC

SDI IN1 SDI OUT1 SDI OUT2

LTC I/O

AES AUDIO RS422

SDI OUT1 SDI OUT2

USB/1394 100BT/1000BT

GPI

VGA REF. LOOP THROUGH

AES AUDIO RS422

LTC I/O

SDI IN2 SDI IN3 SDI IN1 SDI IN2 SDI IN3

SDI IN1 SDI OUT1 SDI OUT2

LTC I/O

AES AUDIO RS422

SDI OUT1 SDI OUT2

AES AUDIO RS422

LTC I/O

SDI IN2 SDI IN3 SDI IN1 SDI IN2 SDI IN3

1. Make cable connections

2. Start up

4. Configure network and, if necessary, storage

Connect

power

cord

Optional Fibre Channel card

for connection to standalone

direct-connect storage or

shared Fibre Channel storage.

Connect

power

cord

Each channel (C1, C2, etc.) can be an input

(record channel) or an output (play channel).

Connect video/audio IN and OUT to each

channel, as appropriate for your intended use.

Bi-directional channels

SDI connections

Press the standby switch

to power on.

Replace the bezel/fan

and identify the following:

Service

LED

Standby

switch

Power

LED

Power LED goes on and

stays on. Service LED

stays off.

Normal startup sequence

Continue with Quick Start procedures on the reverse side.

Make other

connections as

needed. Refer to the

K2 System Guide for

complete

instructions.

Use SiteConfig as appropriate for your K2 system and on-site networking.

Before power on, take

note of the chassis serial

number, located behind

the bezel/fan.

Locate the Recovery Flash

Drive, which is labeled with

this unit’s serial number.

Make sure it remains stored

with this specific unit.

Connect keyboard

and mouse

Connect VGA

monitor

Stand-alone internal or direct-connect storage – Install

SiteConfig on a control point PC, discover the K2 Summit

Production Client, and configure network interfaces.

- Configure Control Team for the control network.

- If desired, configure Media Connection #1 for the

FTP/Streaming network.

Refer to K2 Release Notes for instructions.

Shared storage – Configure network

interfaces as instructed in the K2 SAN

Installation and Service Manual.

Internal storage – No storage configuration is necessary. Storage is pre-configured.

Direct-connect storage – Use Storage Utility to Bind RAID disks and make file system.

Refer to the K2 System Guide.

Shared storage – Use the K2 System Configuration application to add the K2 Summit

Production Client to the K2 SAN and configure it on the SAN. Refer to the K2 SAN

Installation and Service Manual.

Log on with the default

Windows admin account:

-Username: Administrator

-Password: adminK2

3 5

On the Windows desktop, check the system

tray. When the network icon indicates connectivity,

the K2 Summit Production Client is operational.

3 6

3 2

3 1

Configure storage as follows:

Click Start | All Programs | Grass Valley | Write Filter Utility.

FBWF Manager opens.

Set Filter to Disable.

Click OK.

When prompted,

restart the K2

Summit Production

Client.

3 3

5. Configure channels

C1 C2 C3 C4

SDI video in

and out.

Supports

embedded

audio.

LTC

I/O

RS-422

AES audio

Make connections as desired on each channel

1 1

1 2

1 3

1 4 1 51 5

Connect

network cables

to Ethernet

ports

GigE Ports

-Port 1 - Control network

-Port 2 - Media (iSCSI) network

-Port 1 - Control network

-Port 2 - FTP/Streaming

-Ports 3 & 4 - Not used

Internal or direct-connect storage:

Shared iSCSI storage basic:

-Port 1 & 4 - Control network

-Port 2 - Media (iSCSI) network A

-Port 3 - Media (iSCSI) network B

Shared iSCSI storage redundant:

-Port 1 - Control network

Shared FC storage basic:

-Port 1 & 4 - Control network

Shared FC storage redundant:

Ethernet cabling

AppCenter

ppCenter

Open AppCenter and logon with the K2 administrator account

(K2Admin/K2admin). If a licensing message appears, refer to

K2 Release Notes.

Click tabs,

buttons, and

scroll bar to

locate settings.

Select from

drop-down lists

to make settings.

Click OK and

Yes to save

settings.

Click System | Configuration.

DHCP is enabled and the

chassis serial number is

the hostname.

Default network settings

Configure network name resolution via host

files or otherwise, as required by on-site

networking. FTP/Streaming network

hostnames must include “_he0” suffix.

When changes are complete, enable the write filter.

3. Disable write filter

The K2 Summit Production Client has a file-based write filter to

protect from changes and increase on-air reliability. The write filter

must be disabled before making changes and enabled after

changes are complete.

Disable the write filter as follows:

To enable the write filter, set Filter to Enable and restart.

K2 Summit Production Client

Power cords

LTC cables

Release Notes

Licenses and

Warranties

Rack slides

Documentation CD

usss

rass all roup

usss

rass all roup

K2 SUMMIT

PRODUCTION

CLIENT

NOTE: Do not lose the Recovery Flash

Drive that is stored inside the bezel.

It contains the image for this specific

K2 Summit Production Client.

Release

Notes

Documentation path to install

K2 client with internal storage

System

Guide

Quick Start

Guide

Documentation path to install

K2 client with shared or direct-connect storage

Release

Notes

System

Guide

Quick Start

Guide

SAN Manual

(shared storage)

*Cabling Guide packed with RAID primary chassis

*Cabling

Guide

ﬂxxxxx

xxxxxxxxxxxxxx

ﬂxxxxx

Grass Valley

Ethernet connection names

Is named this in Windows

Network Connections...

Control Team (Control

Connection #1)

This rear panel

GigE port...

Media Connection #1

Media Connection #2

Control Team (Control

Connection #2)

IN1 - Active

IN2 - Not used

IN3 - Not used

OUT1 - Active

OUT2 - Monitor Out.

Configurable to

display timecode.

1 2

Inhaltsverzeichnis

Seite 1 - Optional Fibre Channel card

Connections per channel (C1, C2, etc)K2 Summit Production ClientQuick Start GuideBefore you begin, unpack the following items...071-8722-00

Seite 2 - AppCenter Help Topics

5. Record and play8. For more information...1 Select a channel3 Stop record4Drag a clip into the channel2 Begin recordA channel becomes an input chann

Kommentare zu diesen Handbüchern

Keine Kommentare

Grass-valley K2 Summit Client Quick Start Nov.23 2009 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Grass-valley K2 Summit Client Quick Start Nov.23 2009 herunter. Grass Valley K2 Summit Client Quick Start Nov.23 2009 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Grass-valley K2 Summit Client Quick Start Nov.23 2009